Recommended Custom Mounting Brackets for a 2010 Ford F-150 Using a Detail K2 Snowplow

Question

Question:

I recently bought from you a Detail K2 Snowplow for 2inch Hitches - 84inch Wide x 22inch Tall for a Dodge Dakota. Well my Dakota is no longer working and I would like to put this on a 2010 Ford F150. Is there a front mount that will fit this.

asked by: Kathryn A

0

Expert Reply:

Welcome back! Yes, we do have a front mount kit that will get the Detail K2 Rampage II Snowplow item # K2RAMP8219 set up on your 2010 Ford F-150. It is the Custom Mounting Brackets for Detail K2 Snowplows item # K281521.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The Brophy Slide In Camper Tie-Downs #HSAB might be a fit for your 2011 Ford F-150 but you'll need to do a bit of measuring first and you'll likely need to trim out holes where the tie-downs would sit. You'll want to verify that #HSAB…

view full answer...

Answer 3

I checked with Curt and I can confirm that the Curt Front Mount Trailer Hitch item #C22NR does fit the 2022 Chevrolet Silverado 1500 LT with the diesel engine. The only picture we have is from the installation instructions and I have attached it…

view full answer...

Answer 4

Good question! The blade stiffeners that come with the Detail K2 Snowplow #K2AVAL8422 don't necessarily have to be used. I reached out to my contact at Detail K2 who said that the only time that those stiffeners really need to be used is if you…

view full answer...

Answer 5

To use a SnowBear plow with your 2021 GMC Sierra 1500 you'll need to install a front mount hitch like part #C31088 (does not fit a 2.7L Turbo) and then use one of their hitch-mount snow plows like the Personal Snowplow #SB324-080 which is…

view full answer...

Answer 6

I attached a picture that shows the install instructions for the Caster Kit for SnowBear Snowplows #SB324-126 that you referenced.

view full answer...

Answer 7

Apart from the size of the plows, another economic factor is whether the plow is electric actuator driven like the Detail K2 Rampage II Elite Snowplow - Custom Mount #K2RAMP8219ELT or electric winch driven like the Detail K2 Rampage II Snowplow…

view full answer...

Answer 8

Yes, the Draw-Tite Front Mount Trailer Hitch Receiver #DT36MR will fit your 2022 Ram 3500. This has a bolt-on installation with a 9,000 lb line pull and 500 lb vertical load limit. The only exception is if you have a diesel model.

view full answer...

Answer 9

To attach a SnowBear plow to a front hitch like the Curt #C31089 that fits your 2019 Ram 2500 what you need is the hitch adapter part #SB324-120. This will enable your current plow to attach to a hitch so you'd be set with it and the front…

view full answer...

Answer 10

I have a few different options for you, but the Draw-Tite Receiver #65041 is not going to fit a 1998 Toyota 4Runner. If you want to stick with the Draw-Tite brand, I recommend going with the Max-Frame Hitch Receiver #75091. It is a Class III hitch,…

view full answer...

Recommended Custom Mounting Brackets for a 2010 Ford F-150 Using a Detail K2 Snowplow

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching