Replacement Rear Clearance Lights For a Sure-Trac Utility Trailer ST7211HST-B-030

Question

Question:

I have a Sure-Trac trailer model number ST7211HST-B-030, it is a 6x12 tube top 3 board high side utility trailer. Someone tried to remove the three led lights in the rear middle of the trailer and I am looking to get replacements. If you could help me that would be great, if not maybe you know where I can get the replacement lights. I need three. Thank you.

asked by: Gary E

1

Helpful Expert Reply:

Based on images I could find for your Sure-Trac utility trailer model ST7211HST-B-030 it appears is uses either the Incandescent # A91RB or LED # AL91RB lights. These are held in place with the Grommet # A91GB which is 3-5/16" long x 1-15/16" wide. If you have a different style or size light please send me some images with measurements and I can verify what we have for a replacement.

expert reply by: Bud M

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

For the Tecnic 45 degree accent light part #TN42FR the correct mounting cover is the part #TN34FR.

view full answer...

Answer 5

I looked up the towing capacity of your 2015 GMC Sierra 2500HD with a Duramax diesel and it looks to have a 13,000 lb towing capacity like you mentioned. If the trailers you are considering will weigh less than that when loaded and ready to tow…

view full answer...

Answer 6

I had a hard time finding a lot of information using the two part numbers you found both on the lens and the light base. It looks like the base number may refer to the Optronics Trailer Light #MC32AB, for which the correct replacement lens is part…

view full answer...

Answer 7

The most similar trailer clearance lights we offer to replace the PM150 lights you have now would be the Thinline LED light part #AL91RB. For a replacement harness that would plug into this you'd need the part #A46PB and then for a grmmet part…

view full answer...

Answer 8

The studs on the Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles part #AKIHUB-545-35-G-EZ-K are 1-5/16" in length. This is generally a good length for this application. So as long as the slip on rotors you are using require a stud length…

view full answer...

Answer 9

I believe what you are looking for is our part #K12WB2. This has a thread diameter of 1/2 inch, a spline diameter of .54 inch (I know you said .56), and is overall 2 inches. This is our closest option and is a very standard stud seen for trailer hubs…

view full answer...

Answer 10

An EZ lube spindle will be better because it allows you to insert grease from inside the spindle where the bearings are and push out the old grease whereas with a Bearing Buddy you basically just get to push grease through the front of the hub. I…

view full answer...

Answer 11

I do have a few easier options for you to determine the weight capacity of an axle other than using the bolt pattern or the number of lug nuts. The problem with using the bolt pattern to tell the axle capacity is that an axle may have the a bolt…

view full answer...

Replacement Rear Clearance Lights For a Sure-Trac Utility Trailer ST7211HST-B-030

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching