Replacement End Cap for TracRac Ladder Rack Load Bars

Question

Question:

i have track rack. i need black caps 4 at the top left and right of ladder rails.my rack isaround 5 years old.

asked by: Pat S

0

Expert Reply:

It sounds like you are looking for replacement end caps for the ends of the bars on your TracRac ladder rack. For a single replacement use # TA01-27023. It will fit TracRac G2, T-Rac G2, and TracONE truck bed ladder racks.

expert reply by: Michael H

0

Answer 1

I reached out to my contact at Thule the maker of TracRac and the Replacement End Cap for TracRac Ladder Racks #TA01-27023 uses an M6-1 socket head cap screw. We carry only one screw this diameter and head and it is the #TH919063054 which is 30mm…

view full answer...

Answer 2

Replacement End Cap for TracRac ladder racks #TA01-27023 does not come with the set screw. If the old screw is missing you would need to obtain one from a local hardware store.

view full answer...

Answer 3

The Replacement Crossbar for TracRac Ladder Racks - 69-1/2" Long - Qty 1 #TAFX-30007-02 compatible with your SR rack will use the end cap #TA01-27023. This threaded end cap will replace your missing end caps. The screw you will need for this…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement End Cap for TracRac Ladder Rack Load Bars

Product Page this Question was Asked From

Continue Researching