Recommended Replacement Coupler for a Bulldog

Question

Question:

Do you have a bulldog sleeve coupler repair kit for the low profile slide lever latch?

asked by: Robert W

0

Expert Reply:

We unfortunately do not have the coupler repair kit you're looking for because it's been discontinued. I'd recommend just replacing the entire jack with a new one like the Bulldog Round, A-Frame Jack # BD1550100317. This is a sidewind jack that has a 3,000 lb capacity, 13" of lift, and can be bolted or welded on.

expert reply by: Bryce D

0

Answer 1

The Sleeve-Lock A-Frame Trailer Coupler #CA-5196-B was designed for attaching to the standard 50 degree a-frame channels found at the front of trailers. If you have a different angle that doesn't sit flush a better choice might be to go with a…

view full answer...

Answer 2

A trailer is always going to be limited by its weakest component. This means that even if everything else on the trailer (axle, hubs, wheels, suspension, etc) is rated for 7,000 pounds, you will still need to adhere to the 5,000 pound limit on the…

view full answer...

Answer 3

I recommend having the Demco A-Frame Trailer Coupler #DM14791-97 welded on in place of the Sleeve-Lock #CA-5196-B style coupler that you currently have. This Demco coupler uses a 2" hitch ball the same as your current coupler and is rated for up…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Recommended Replacement Coupler for a Bulldog

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching