What Do I Do With The Factory Jounce When Installing Air Lift AL57344 On A 2012 Ford F-53?

Question

Question:

Airlift 57344 install on 2012 F-53 Newmar Baystar. Instructions are to remove factory jounce bumper and save for layter use. No further mention of this. Do they get reinstalled? Tia.

asked by: Michael

0

Expert Reply:

The factory jounce bumpers will not be reinstalled when installing the Air Lift # AL57344 on a 2012 F-53 Newmar Baystar. So there really is no need to save the factory jounce. Sometimes if there is a bolt holding the factory jounce on you will want to keep the bolt. The only reason to keep the factory jounce would be if you ever needed to remove the air bags for some reason.

expert reply by: Jesse M

0

Answer 1

The Air Lift kit part #AL57344 that fits your 2019 Ford F-53 has a capacity of 5,000 lbs and that might be a confusing figure. What it is supposed to indicate is that it can provide up to an additional 5,000 lbs of suspension support. So your RV…

view full answer...

Answer 2

The Air Lift kit part #AL57344 that you referenced is a confirmed fit for your 2016 Ford F-53. It will provide up to 5,000 lbs of suspension support to bring your vehicle back to level if is carrying a heavy load. If you are sagging 4-5 inches this…

view full answer...

Answer 3

In regards to the Air Lift LoadLifter 5000 Air Helper Springs part #AL57344, you'll still be able to raise the rear of the motorhome for leveling but if you're doing so for service and the rear axle would be suspended, then you would want to…

view full answer...

Answer 4

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

What Do I Do With The Factory Jounce When Installing Air Lift AL57344 On A 2012 Ford F-53?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching