Recommended Front And Rear Anti-Sway Bars For A 2011 Ford E-350 Van

Question

Question:

Hi, i have a ford E350 v8 5.4l single wheel I want to add a sway bar in the back and maybee put a better one in the front what do you suggest me? Thanks.

asked by: Jeff

1

Helpful Expert Reply:

For a 2011 Ford Van on an E-350 Chassis you would need the Roadmaster Rear Anti-Sway Bar # 1139-178 and the Roadmaster Front Anti-Sway Bar # RM-1139-115.

expert reply by: Kevin C

1

Answer 1

The Roadmaster Rear Anti-Sway Bar, part #1139-178 is still an active part and available from us. This 1-1/2 inch diameter sway bar is designed to fit Ford E-350 vans and includes the hardware needed for installation. This anti-sway bar will help…

view full answer...

Answer 2

If there is no anti-sway on the rear suspension then I would consider starting there, I suggest the Roadmaster Rear Anti-Sway Bar, #1139-178 designed to work in conjunction with current suspension system, attaches to rear axle and to chassis uses…

view full answer...

Answer 3

Yes we do! The Roadmaster Rear Anti-Sway Bar #1139-178 is designed specifically for the 2-wheel drive E-350 chassis that your 2008 Pleasure-Way Pleasure Way Class B is built on. It features a 1-1/2" diameter bar which is much more effective than…

view full answer...

Answer 4

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 5

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 11

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 12

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Recommended Front And Rear Anti-Sway Bars For A 2011 Ford E-350 Van

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching