Is the H-Channel for Enclosed Trailers Available in Different Sizes?

Question

Question:

I have this part in my cart now but i need the same part in 3/4 wide. Do you have a part number for this? H-Channel for Enclosed Trailer - 93-1/2 Long x 2 Tall x 1-1/8 Deep - Aluminum - 36281-955

asked by: Dave F

0

Expert Reply:

The H-Channel # 36281-955(93-1/2 Long x 2 Tall x 1-1/8 Deep) you found is the only size H-Channel we currently carry.

expert reply by: Bud M

0

Answer 1

Yes, we do have some "H" channel that is designed to be used for enclosed trailer cabinets and doors. - H-Channel for Enclosed Trailer #36281-955 The #36281-955 measures 93-1/2" long x 2" tall x 1-1/8" deep and can be cut to…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 9

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 10

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 11

You will want the hitch to be set at the height that 1) allows the trailer to be level, and 2) allows you a minimum of 6 inches between the bottom of the trailer loft and the top of the bed rails. The fifth wheel hitches offer several inches of up…

view full answer...

Answer 12

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Is the H-Channel for Enclosed Trailers Available in Different Sizes?

Product Page this Question was Asked From

Continue Researching