Steering Stabilizer for Motor Home Built on 2002 Chevy Express Van 3500 Chassis

Question

Question:

I have a B class motorhome . It looks like a Van and weighs 9000 lbs on a 2002 Chevrolet 3500 chassis. It is 21inch long . Is this the right one for my Roadtrek motorhome.????

asked by: Evelyn

0

Expert Reply:

Yes, for the 2002 Chevy Express Van chassis 3500 you would need steering stabilizer # RM-RBK15-RSSC that you have referenced. I have also included a link to our help article on heavy duty stability control for you to view.

expert reply by: Michael H

0

Answer 1

Yes, for the 2000 Chevy Roadtrek Express Class B chassis 3500 you would need steering stabilizer #RM-RBK15-RSSC that you have referenced.

view full answer...

Answer 2

Since it's a Class B RV your chassis is a cutaway so the correct rear sway bar is the part #RM-1109-175-00 but we do not have a front bar for your RV chassis. The good news is that the rear bar is the one that makes the biggest difference by…

view full answer...

Answer 3

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 4

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Steering Stabilizer for Motor Home Built on 2002 Chevy Express Van 3500 Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching