Availability Of A 15" Wheel With 5 On 5-1/2" Bolt Pattern

Question

Question:

I need a 15inch wheel with a 5x5.5 pattern and a 3 1/4inch apart. Can you help?

asked by: Angel

0

Expert Reply:

We do carry one wheel that fits those specifications with part # TA37RR. This is a 15" wheel with the 5 on 5-1/2" bolt pattern (holes 3-1/4" apart on center). It is important to note that this wheel is made with a -0.67" offset, so the tire will sit slightly farther from the trailer than it would with a standard non-offset wheel.

expert reply by: Jesse M

0

Answer 1

You want to make sure the hangers on your trailer have the same width as your leaf spring so if your leaf spring is 1-3/4" wide then you don't want to use a 2" or 2-1/2" wide hanger. It's true that you want the hanger bolts…

view full answer...

Answer 2

I am not really sure what the dealership was referring to as a 22 axle but we do have options for you to lower your trailer. The first option if you have a leaf spring axle is an over/under kit like the Dexter Trailer Springs Over-Under Conversion…

view full answer...

Answer 3

When it comes to lowering your trailer 2-2.5 inches if your have leaf springs and they're positioned above the axle tube, you can flip them with the Dexter Trailer Springs Over-Under Conversion Kit #K71-385-00 if you have a 3 inch diameter axle…

view full answer...

Answer 4

I was able to look at the picture of your trailer wheel/tire and see that the size is 7.00-15LT so for a wheel in the 15 inch diameter that has the 5 on 5-1/2 inch bolt pattern that you need we have one option with the part #TA37RR. Since your…

view full answer...

Answer 5

Great question. As a general rule, when your trailer is loaded to it's full capacity, there should be a minimum clearance of 3 inches between the top of your tire and the underside of your fender.This should give you adequate clearance for…

view full answer...

Answer 6

There are no 16 inch trailer wheels with a 5 on 5-1/2" bolt pattern, so you'd have to stick with the 15 inch wheels:: - Vesper Steel Modular Trailer Wheel w/ Offset - 15" x 5" Rim - 5 on 5-1/2 #TA37RR This has a -0.67" offset,…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Availability Of A 15" Wheel With 5 On 5-1/2" Bolt Pattern

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching