Hub with Bearings that Fits BT8 2k Axle Trailer Spindle TRU94FR

Question

Question:

I am building a small farm cart. Max capacity will be 4,000 lbs. can you give me a lto the bearings, hub, rim please that would work with this weld on spindle? Do you have a dimension for the length of the section that will be welded? Thx,

asked by: Karl K

1

Helpful Expert Reply:

The BT8 spindle part # TRU94FR that you referenced is designed for 2,000 lb axles so for a hub that would fit this you would want the # 8-259-5UC1-EZ which comes with the correct bearings installed and is pre-greased and ready to install. The weld on portion of the spindle is 3-1/4 inches long.

expert reply by: Jameson C

1

Answer 1

I have a replacement axle option for you, but unfortunately the inner bearing #L44649 and outer bearing #LM11949 combination your utility trailer axle uses is not one that is common any more, and as such there is not any replacement hubs available.…

view full answer...

Answer 2

The hub assembly we offer for a 2,200-lb EZ-Lube axle is part #8-259-50UC1-EZ. This hub has a zinc plating that makes it great for snowmobile trailers or boat trailers. The Inner bearing and race, outer bearing and race, grease seal, grease cap, and…

view full answer...

Answer 3

Since your Carry-On 5' x 8' Utility Trailer has a 2000lb GVWR it more than likely has a 2000lb axle and would need a hub that uses either inner and outer bearings #L44643 or #L44649. I know on The 5' x 8' Carry-On Trailer I bought…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Hey Tommy, yeah we have quite a few hubs that fit the Lippert 2,200 lb axle spindles like the part #8-258-50UC1 which is an idler hub with a 5 on 4-1/2 inch bolt pattern. I also attached a link to a page that has all of the 2,200 lb hubs we offer as…

view full answer...

Answer 12

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Hub with Bearings that Fits BT8 2k Axle Trailer Spindle TRU94FR

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching