Recommended Replacement Braking Assemblies for a 2018 Coyote Trailer W/ 3.5K Axles

Question

Question:

Looking for brakes and bearing kit for 2018 coyote trailer with two 3500lb axles with torsion spring.

asked by: Patrick

0

Expert Reply:

For 3,500 lb axles, you can use the Electric Trailer Brake Kit # AKEBRK-35-SA to replace your brakes, however for your bearings you are going to need to actually pull off the bearings you're needing to replace and look for the number stamped on it; i.e. L68149 or L44649.

I've attached a FAQ that goes into a bit more detail when it comes to finding the correct bearings.

expert reply by: Bryce D

0

Answer 1

Yes, the Kodiak Disc Brake Kit item #K2HR35DS. Those are 10" Hub/Rotor with a 5 on 4-1/2 bolt pattern that will fit 14"-15" wheels. The hubs are corrosion resistant with a dacromet plating. They are sold in pairs so you…

view full answer...

Answer 2

More than likely the DeeMaxx Disc Brake Kit #DE42FR will fit your 2021 Coyote trailer. You will need to verify that your existing brakes use slip-on rotors and your current bolt pattern is 5 on 4-1/2. If that is accurate then these will work for…

view full answer...

Answer 3

We do have some options for replacing the Knott calipers and rotors on your Coyote Boat Trailer. We really do not have any info or specs on the Knott brand brakes, but since it is all for a 3,500 lb axle the sizing should be standard. Standard…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 12

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Recommended Replacement Braking Assemblies for a 2018 Coyote Trailer W/ 3.5K Axles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching