Is Brophy Camper Tie Downs part # HSAB Only Sold in Quantity of 4

Question

Question:

I only need 2. can i buy a pair or do i have to buy 4 2019 ram 2500 6.5 bed

asked by: Darren B

0

Expert Reply:

At this time we only offer the Brophy Camper Tie Downs part # HSAB sold in a quantity of 4.

expert reply by: Jameson C

0

Answer 1

Brophy does not have a fit list for tie-downs #HSAB so you have to go by how they install. The external bed rail width cannot be more than 5-1/2 inches wide. There will need to be at least 2 inches space under the lip of the bed rail. And they are…

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 5

The Torklift Hitch Extension part #TLE1636 that you referenced can tow a trailer that weighs 6,700 lbs like you what you have but you would need to use a weight distribution system with it to have the needed capacity as without a WD system it's…

view full answer...

Answer 6

According to CR Brophy, the camper tie down brackets you'd looked at, part #HSWB are specifically designed to fit the bed of a 2019 Ford F-250 and 350. There does indeed need to be 2 inches of available space under the lip of the truck bed side…

view full answer...

Answer 7

Yes, the Brophy camper tie downs like the #HSAB can be used with bed rail covers. If you check out the picture I attached you can see a set installed on a bed rail with plastic covers.

view full answer...

Answer 8

The Brophy Slide In Camper Tie-Downs #HSAB might be a fit for your 2011 Ford F-150 but you'll need to do a bit of measuring first and you'll likely need to trim out holes where the tie-downs would sit. You'll want to verify that #HSAB…

view full answer...

Answer 9

There is no weight capacity for the Brophy Clamp On Camper Tie-Downs #HSSF. The tie-down hardware kit #TDHP, that is used to secure the camper to the #HSSF tie-downs has a weight capacity of 3,000-lbs. My contact at Brophy said the tie-downs will…

view full answer...

Answer 10

The Angled Hold-Downs for Truck Bed Campers #HSAB should work very well for your 2003 Chevy Silverado 2500. We had a customer leave us a review that said they were very easy to install and reinstall and that it only took a few minutes, so I think…

view full answer...

Answer 11

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 12

The RoadActive Suspension Custom Leaf Spring Enhancement Kit #RAS54FR will raise the rear stock height of your 2023 Chevy Silverado 1500 by 1/2" - 1-1/2" according to RoadActive. The variances being the amount of tension you choose to set…

view full answer...

Is Brophy Camper Tie Downs part # HSAB Only Sold in Quantity of 4

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching