Size of Rotor on Kodiak Disc Brake Kit K2R35D

Question

Question:

On our project we need a 10 inch diameter rotor, because I we are using a 14 inch rim/tire assume. Do you have 10” diameter rotors. We are I working on a 1930 Ford project. Last question if we order the K2R35D kit and it doesn’t work out will you handle the return shipping?

asked by: Merril

0

Expert Reply:

All of the rotors for 10 inch disc brakes are technically 10-7/8 inches, including the rotor for the Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs # K2R35D.

This does work with 14 inch and larger wheels. We will not handle return shipping, and only unused products can be returned.

expert reply by: Kyle S

0

Answer 1

The slip-on rotor included with the Kodiak #K2R35D disc brake kit have an inside diameter of 6.681 inches and an outside diameter of 10.875 inches, as shown in the provided photo. The rotors are compatible with hubs that have a 5 on 4-1/2 inch bolt…

view full answer...

Answer 2

In order to determine the correct placement for the brake mounting flange, you will need to put all wheel components together in the proper order on the spindle and then mark the location for the brake mounting flange. The brake mounting flange needs…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Size of Rotor on Kodiak Disc Brake Kit K2R35D

Product Page this Question was Asked From

Continue Researching