Does The Fastway WD System # EQ91-00-6100 Use Grip Tape Between The Bars And Brackets?

Question

Question:

I have the e2 round bar 8000lb. Its 3 years old and the friction tape on what ever it is is completely gone off the bars and brackets from my last camping trip. Do you offer replacement grip or what can I use to replace it?

asked by: Josh

0

Expert Reply:

The Fastway e2 round bar system # FA94-00-0800 uses steel on steel friction. When The L brackets are manufactured, they do sand a small section of the paint so it is not smooth. You can see the small sanded portion in the picture below. There should not be any kind of grip tape between the bars and the brackets. The steel on steel friction by itself is enough.

expert reply by: Jesse M

0

Answer 1

Hey Pat, thanks for reaching out and the photos! The Mount-n-Lock SafetyStruts Standard RV Bumper Support Brackets #MO22FR looks like it will work on your application, but you'll need to more your rear jacks around to make more room, and cut off…

view full answer...

Answer 2

To determine the correct replacement slide out motor you would need to first find the motor and get a picture of the ID tags that can be on either motor or gearbox, or in some cases on both. We can use these parts numbers to cross reference to…

view full answer...

Answer 3

I really don't have a good answer on why the MORryde Safe-T-Rail Telescoping RV Hand Rail #MR54BR can't be used on a class A motorhome. Realistically, as long as the surface that this is being installed onto is completely flat, free of…

view full answer...

Answer 4

You have to get to the topside of your trailer because the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF is located on the top of the vent.

view full answer...

Answer 5

If you're referring to the control module #LC85ED for your Ground Control 3.0 #LC675817 then yes, each fuse is to power each individual leg and should be labeled with which specific leg. If you're moving the slides at the same time while the…

view full answer...

Answer 6

I spoke with Lippert about the dimensions regarding the Replacement Front Panel Module for 17" and 21" Tall Furrion 2-in-1 Range Ovens #FR83RV and they let me know that it is 4.5" tall, 20" long, and 21.5" wide.

view full answer...

Answer 7

Yes, you can open the bottom box with the top box mounted with the Yakima EXO #Y74ZR in the two-box configuration. The top level can be rotated 180 degrees, which will allow you to open the bottom box. We are not aware of any fitment issues with the…

view full answer...

Answer 8

To determine the bolt pattern of your 2018 Nitro Z18 boat trailer you'll need to first count the bolt holes on your current wheel. If you have an even amount of bolt holes then you can measure from the center of one hole to the center of the hole…

view full answer...

Answer 9

I went out to the warehouse and pulled the Propane RV Range with Glass Cover #FR97KR and drew up some dimensions for you. The handle on the door sits 2" out from the door and the door is 21-1/2" wide. The #FR97KR has two rack positions…

view full answer...

Answer 10

I went out to the warehouse and measured the Gooseneck Coupler Handle #GCPN-HD and measured 8 1/2" overall, 3 1/4" for an overall height, 2 1/2" for an inside measurement, and is 12.95 mm (.5") thick. I've attached a diagram…

view full answer...

Answer 11

No, you do not! The etrailer Hitch item #e43ZR does not require any cutting of the trim to install on the 2023 VW Tiguan. This hitch is custom fit and bolts to your VW with included hardware. This is a class III hitch with a 2" receiver. It has…

view full answer...

Answer 12

Below the bumper. The Curt Trailer Hitch item #C26VV mounts to the bottom of your 2024 Toyota Grand Highlander's frame and extends out below the bumper and trim. This installation method requires no cutting of your trim or fascia. The Curt item…

view full answer...