Replacement for 1/2"-20 Wheel Bolt Measuring 2" Long and Just Over 1/2" Spline Diameter

Question

Question:

I am looking for a wheel stud for a freedom axle. It is a 1/2x20 2 inch long with a spline diameter of.561. Would you have anything that would word? Thanks.

asked by: Josh H

0

Expert Reply:

The closest thing we have to what you're needing is the Kodiak Wheel Bolt # K12WB2 which is a 1/2"-20 bolt measuring 2" long and has a 0.54" spline diameter so it will work well for your application.

expert reply by: Jon G

0

Answer 1

It sounds like the Trailer Hub Wheel Stud - Drive In - 1/2" Diameter x 2" Long - Qty 1 #7-122 is what you're looking for. This is a 1/2" x 20, 2" long stud with a .61 spline diameter-which is the closest we've got to your…

view full answer...

Answer 2

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

Unfortunately we do not have a way to replace the keys without knowing the key number for the lock. If they happened to have written down the key number from the lock then we will be able to get you a replacement. The etrailer Trailer Hitch Receiver…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Base plate kits are somewhat time consuming but they aren't too terribly long. I once asked our install guy that's been here forever how long to set aside for a base plate kit install and he said a "long afternoon" and you'd be…

view full answer...

Answer 11

The tires on your trailer should not come off the ground while leveling. It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix…

view full answer...

Replacement for 1/2"-20 Wheel Bolt Measuring 2" Long and Just Over 1/2" Spline Diameter

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching