How Does Tightened Pivot Bolt of Roadmaster Tow Dolly Allow Movement

Question

Question:

IF I torque the pivot bolt to 70ft/lbs and the pad is tight how will the deck swivel thank you

asked by: Gerard

0

Expert Reply:

While the pivot bolt part # RM-350800-00 is torqued down pretty tight the wear plate that goes between the two moving pieces allows the movement.

expert reply by: Jameson C

0

Answer 1

In order to switch from your electric brakes to a disc brake system there are several things you will want to consider. It is true that the disc brakes will provide better braking for you, although converting can require an involved installation.…

view full answer...

Answer 2

Since the install of the pivot bolt part #RM-350800-00 that you referenced requires 70 ft lbs there wouldn't end up being any clearance between the pad and the pivot bolt nut. The pad ends up getting bolted to the deck.

view full answer...

Answer 3

I was able to confirm that the diameter of both the Replacement Steering Pin and Clip #RM-357100-00 and your Master Tow tow dolly are both 5/8" in diameter. You will be able to use the Roadmaster Pin on your Master Tow dolly.

view full answer...

Answer 4

The Replacement Pivot Bolt for Roadmaster Tow Dolly with Electric Brakes - Qty 1 #RM-350800-00 as you stated does not come with any additional hardware. Currently the only way to get the bolt and nut is to get the Roadmaster Tow Dolly Ramp Wear Strip…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

SumoSprings would definitely be the solution I would recommend for your squatting concern. The SumoSprings Solo Custom Helper Springs - Rear Axle item #SS45MR have a 2,800 lbs capacity which would eliminate that carolina lift look you get when your…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

How Does Tightened Pivot Bolt of Roadmaster Tow Dolly Allow Movement

Product Page this Question was Asked From

Continue Researching