Correct Replacement Step Motor for Kwikee 28 Series Steps

Question

Question:

Looking for a control motor for a series 28 Kwikee power step Control motor #909501 Serial # 46195

asked by: Bob

0

Expert Reply:

The correct replacement motor for your Kwikee 28 Series steps is the Replacement Motor with Mounting Plate for Kwikee Electric RV Steps # LC379608.

expert reply by: Bryce D

0

Answer 1

I spoke with Lippert and their tech stated that the replacement motor for your model would be Replacement for Kwikee Electric RV Steps #LC379608 but that due to the age of your steps that it might not be compatible with the other electrical…

view full answer...

Answer 2

It looks like you've got a Kwikee step motor 5973820 and according to my tech contact at Lippert the correct replacement motor is the Lippert Components Kwikee Step Motor Replacement Kit #LC379608. This is a direct replacement for your old…

view full answer...

Answer 3

I spoke with my contact at Lippert regarding your existing motor/gearbox model 5973820. He stated that the correct replacement motor is the Lippert Components Kwikee Step Motor Replacement Kit #LC379608. This is a direct replacement for the motor…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Correct Replacement Step Motor for Kwikee 28 Series Steps

Product Page this Question was Asked From

Continue Researching