Installation Process For A Trailer Brake Controller In A 2022 Toyota Highlander

Question

Question:

TRAILER BRAKE CONTROLER INSTALATION 2022 TOYO HIGHLANDER NON HYB

asked by: Jeffrey B

0

Expert Reply:

Before you can install a trailer brake controller in your 2022 Toyota Highlander you'll first need to make sure that you have a 4-pole wire harness for your lights installed and then a 7-way wire harness to get your brake function. If you don't already have a 4-pole installed then you'll want the Tekonsha # TK74FR if you have a factory tow package or the Curt # C59236 if you don't. From there you can install a 7-way # ETBC7.

The # ETBC7 will have a 4-pole connector to connect to the 4-pole wire harness for the light functions. You'll also have a white ground wire to run to the frame and a yellow reverse light wire that you can just cap off with electrical tape unless you have a boat trailer with an electronic lockout for the brakes. The black wire will run up to the battery with one of the included circuit breakers spliced inline. The blue wire will run to the cab to connect to your brake controller. I've attached a video of this process that Conner made to walk you through it.

I see that you're looking at the Tuson DirecLink Base Model Trailer Brake Controller # 335DL-100, which to be honest I'm not a huge fan of. It's super easy to install but the handheld remote is a bit dated in my opinion and tends to be in the way when not in use. I've attached a video below where I'll walk you through the installation process step by step.

If you haven't purchased your brake controller yet then I highly recommend the Redarc Tow-Pro Liberty Brake Controller # RED24FR instead. This system has a much smaller control knob that can be drilled into the dash or into a blank switch panel (depending on size). We offer a few different options for this: # 331-TPSI-002, # 331-TPSI-001, # 331-TPSI-007. Since there isn't a plug-in option for your vehicle you'll also need to pick up a universal wire harness # RED69FR.

If you have any other questions please submit another question and I'd be happy to help.

expert reply by: Kevin C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

We can definitely get you set up. For a 7-way wiring harness for your 2024 Honda Pilot trailsport I recommend the Curt T-Connector #C35ZV which will plug in to the existing tow package connector at the rear your vehicle. I do also recommend getting…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 8

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Installation Process For A Trailer Brake Controller In A 2022 Toyota Highlander

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching