Parts Need to Install a Redarc Tow Pro Liberty Brake Controller in a 2023 Toyota 4Runner

Question

Question:

What parts do I need to install a Red Arc Liberty Brake controller in a 2023 Toyota 4Runner?

asked by: Lucas

0

Expert Reply:

To install a Redarc Tow Pro Liberty in your 2023 Toyota 4Runner you will need the following parts:

Redarc Tow-Pro Liberty Brake Controller item # RED24FR

Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item # RED49FR

Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob item # 331-TPSI-002

expert reply by: Jerred H

0

Answer 1

To determine where the problem is first disconnect the trailer from the tow vehicle. Use a circuit tester such as #PTW2993 or a meter if you have one to test the vehicle side trailer connector while the head lights are on. If there is power on the…

view full answer...

Answer 2

You are probably on the right track in thinking a grounding issue is at fault. Often if a trailer has a weak or marginal ground connection it will be able to pass enough current for lower current draw lights (such as the turn signals that are not on…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 7

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 8

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 9

The manufacturers do not typically provide the static weight limit of the roof racks. A lot of that reasoning is that the static load limit is typically higher than the cars roof capacity. What I can tell you is that the Malone AirFlow2 Roof Rack…

view full answer...

Answer 10

The Timbren Active Off-Road Bumpstops part #TABSTORSEQ which are a fit for a 2023 Toyota 4Runner are pretty similar to the SumoSprings Solo Custom Helper Springs like part #SS68DR. The Timbrens provide more support but the SumoSprings ride smoother.…

view full answer...

Answer 11

Yes there is! The Touring Awning Room #ARB84FR will be the correct room add on for the 8' 2" Long x 6' 7" Wide ARB Awning #ARB34FR. These rooms are great because they include a waterproof floor, and zippered access doors on every…

view full answer...

Answer 12

The side plates on the 3" Wide Continuous Hinge #MA65VR you found are 0.09" thick which is just under 3/32". We do have a 3" Wide #MA52VR which is 6' Long with a 1/2" pin that has 0.18" thick side plates which is…

view full answer...

Parts Need to Install a Redarc Tow Pro Liberty Brake Controller in a 2023 Toyota 4Runner

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching