Can Different Marine Grease Be Mixed Together If They Have The Same Base

Question

Question:

Can Lubrimatic marine trailer wheel bearing grease be mixed with Lucas marine wheel bearing grease ? They are both calcium sufonate based, I think.

asked by: Frank

1

Helpful Expert Reply:

While it's not recommend, bearing greases with the same base like the LubriMatic Marine Trailer Wheel Bearing Grease # L54FR and your Lucas marine bearing grease can be mixed as long as long as they have the same base.

expert reply by: Kevin C

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Can Different Marine Grease Be Mixed Together If They Have The Same Base

Product Page this Question was Asked From

Continue Researching