Are The DeeMaxx Disc Brake Kits Compatible With The Dexter A-60 Actuator

Question

Question:

Do these work with a Dexter A60

asked by: Rob

0

Expert Reply:

Yes, you can absolutely use the DeeMaxx # DE22FR with a Dexter A-60 Actuator like the # DX56FR. The Dexter # DX56FR actuator is designed to be used with disc brakes. You could use this with virtually any disc brake kit, regardless of brand.

expert reply by: Jesse M

0

Answer 1

The Kodiak Dacromet Disc Brake Conversion Kit, item #K2HR35D, would be a good choice for conversion to disc brakes on your boat trailer. We have not had the opportunity to do a video installation for the disc brake conversion yet, but I will go…

view full answer...

Answer 2

The short answer is Yes, bearing #15123 is slightly larger and stronger than #LM67048 and they use different races which means they are not interchangeable. Bearing 15123 uses race #15245 which has an outer diameter of 2.441 inches and bearing…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Are The DeeMaxx Disc Brake Kits Compatible With The Dexter A-60 Actuator

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching