Can The RV Flooring Adhesive # TS76FR Be Used On Marine Grade Plywood?

Question

Question:

Can this adhesive be used on marine grade plywood? Going to be used with fiberglass backed sheet vinyl in a van conversion.

asked by: Jim B

0

Expert Reply:

Yes, the RV Flooring Adhesive # TS76FR can be used on your marine grade plywood. It will allow you to install your fiberglass backed sheet vinyl in your camper van conversion.

expert reply by: Bud M

0

Answer 1

To install the Small Coin Pattern Vinyl Flooring #TS97FR with the RV Flooring Adhesive #TS76FR you just need to make sure that your trailer floor is a bare wood so you have the best bonding of the adhesive as possible. Be sure to sweep it out really…

view full answer...

Answer 2

No, the thickness of the: -RV Vinyl Flooring #TS56FR is 0.65mm thick not .65", so it's about as thick as a credit card. We do also offer a couple other sizes of lengths if you're interested: -For 12', we have #TS29FR, & -For…

view full answer...

Answer 3

The RV Flooring Adhesive for Vinyl Over Wood #TS76FR that you referenced can't work on a painted surface directly but can if the paint is removed.

view full answer...

Answer 4

The RV Flooring Adhesive for Vinyl Over Wood #TS76FR is designed for trailers that sit out in the elements full-time so yes, it will withstand high temperatures in a van that's sitting out in the sun all day.

view full answer...

Answer 5

The mat #VTFT15L is die cut to the contours of your vehicle, filling the space between the ribs for a smooth, tight, customized fit. Because of that it does not require an attachment setup.

view full answer...

Answer 6

The correct VanTred Custom Floor Mat for Cargo Vans - Black - Thermoplastic for a 2021 Ford Transit T350 DRW is part #VTFT15LE. This van mat is a custom fit for your floor so there's no cutting required and you'll get a very tight fit. It…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Can The RV Flooring Adhesive # TS76FR Be Used On Marine Grade Plywood?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching