Where Are Superwinch Winches Made

Question

Question:

Where is this winch made? USA? China?

asked by: Tom

0

Expert Reply:

The Supwerwinch # SW49GR is made in China. R&D and distribution is based out of California, but the winches are not made here.

expert reply by: Jesse M

0

Answer 1

Yes, the Bulldog Winch Hitch Mounted Winch Mounting Plate with Handles part #BDW20011 will work with the Warn Electric Winch M12 as they both use the same industry standard winch mounting hole spacing which is 4-1/2" wide x 10 long.

view full answer...

Answer 2

From what I was able to find, the Warn M12000 winch is 24.37" L. x 8.45" D. x 11" H. I've attached a picture with the dimensions on the Bulldog Winch Hitch Mounted Winch Plate #BDW20011 but since the mounting cradle is only…

view full answer...

Answer 3

The plate that the winch mounts to is 1/4 inch thick. This mount has 2 sets of four (eight) holes, centered on the cable opening, in a rectangular pattern for mounting the winch to the plate and the measurements are 6-1/2 by 4-1/2 inches on center…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I do have an option for you but the ComeUp Seal Slim Gen2 Off-Road Winch - Synthetic Rope part #CU295057 is a foot forward mounted winch only which is not very common. The standard mounting position of a winch is feet down, I recommend to use the…

view full answer...

Answer 6

While we do have a U.S.A. made option, the Bulldog Winch #BDW15018 is made in China. For a great American alternative, the highest capacity U.S.A. made winch we have is the Dutton-Lainson StrongArm Electric Winch w/ Pulley Block, AC Powered #DL24876.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You can use that upper hole on your hanger to install the #MR33WR. Make sure you don't tighten it down too much or you will pinch the leaf spring and it won't function properly. You will also need to make sure you have enough room to install…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Quite accurate; the margin of error is 3 percent for the etrailer Tongue Weight Scale for Campers and Utility Trailers - 2,000-lb Capacity #e99044. I don't see varying levels of liquid in the photos, but do see a customer photo with the scale…

view full answer...

Answer 11

You need to adjust the tension on your B&W Companion, #BWRVK3715. This done by adjusting the castle nuts, please view the attached installation video.

view full answer...

Answer 12

The Timbren kit #TFR250SDJ does not require a mounting plate above the axle as it is designed to contact the round the plate that is currently on the axle that is mounted below the spring pack. I would recommend sticking with this kit even though you…

view full answer...

Where Are Superwinch Winches Made

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching