Solution for Adding Wheel to Jack on 2002 Rockwood Freedom 1980

Question

Question:

Greetings, I have 2002 Rockwood Freedom 1980 camper. I would like to get a wheel for the trailer jack so that I could move the camper without the car. My tube outer diameter on the bottom is 1.7 inch. Do you have any solution for the issue? Thanks in advance

asked by: Alexander B

0

Expert Reply:

I do have a solution, but all of our wheels fit a 2" diameter tube. With a 1.7" measurement you won't find anything that fits your current jack. The only way to add a wheel will be to get a new jack like the A-Frame Trailer Jack with Caster Wheel # DL74MR. As far as I can tell, you have an A-frame jack right now so this will work as a replacement. It has 15" of travel and a 1,000 lb weight capacity which should be plenty for your camper.

expert reply by: Robin H

0

Answer 1

The a-frame trailer jacks all use a standard mounting pattern and center hole size for the most part so although I am not quite sure what you are measuring I can confirm we have options, the Ultimate Trailer Jack part #322-RDJ-2K is a good one…

view full answer...

Answer 2

Yes, about 99 percent of A-frame jacks use the same mounting pattern. The holes are generally 3 inches apart on center though it can vary ever so slightly which is why some jacks have slotted holes.

view full answer...

Answer 3

We do have one jack available that will fit a 6" frame like yours, that is the Fulton Marine Jack - Square Tube, Fixed Mount - 28" Lift - 5,000 lbs #HD50000101. The largest set of U-bolts that comes with this jack measures 6-1/8" so it…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 9

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…

view full answer...

Answer 10

Yes, you can! So long as our Kenda Loadstar 5.30-12 Bias Trailer Tire with 12" White Wheel item #AM30820 is the same size and bolt pattern as what's on your Ironton trailer it can be used not only as a spare but also on your trailer with the…

view full answer...

Answer 11

The Flint Hill Goods Square LED Brake Light Hitch Cover for 2" Hitches #FHG72VR would indeed be compatible with the #118384 on your 2012 Chevy Colorado. Using the turn signals will not cause the hitch cover to blink. The cover will light when…

view full answer...

Solution for Adding Wheel to Jack on 2002 Rockwood Freedom 1980

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching