Replacement OEM Puck Anchors for Curt A25 5th Wheel Hitch

Question

Question:

I need a complete set of four 4 puck system bolts for a CURT A 25 fifth wheel Hitch

asked by: Michael S

0

Expert Reply:

The correct set of replacement Curt A25 anchors just depends on what vehicle you're needing them for! Here are the different options:

- Ford Anchors # C98UR
- Ram Anchors # C68UR
- Chevy/GMC Anchors # C93UR

Let me know if you're needing anything else!

expert reply by: Jon G

0

Answer 1

Thanks for the picture of Curt Q25 handles you need. Based on that the correct replacement is the part #C38UR.

view full answer...

Answer 2

The correct replacement anchor kit for the Curt GM Fifth Wheel Adapter part #C88KR is the part #C93UR which is the same as the 19210.

view full answer...

Answer 3

The Replacement Anchors for Curt 5th Wheel Hitches for Chevy/GMC OE Towing Prep Package - Qty 4 #C93UR is meant to be a direct replacement part for a Curt 5th wheel hitch that fits in OEM Prep packages; it will not change the size of the anchors on…

view full answer...

Answer 4

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 5

I went out into our warehouse and measured the overall height of the Replacement Quick Turn Puck #116517 and found it to be 2-1/8 inches.

view full answer...

Answer 6

To replace the 4 linchpins that are used to secure the Reese 5th Wheel Rail Adapter #RP30154 to the OEM puck system on your 2021 Ram 2500 you need part #LP316 which is 1-3/8" long and has a 3/16" diameter.

view full answer...

Answer 7

I spoke with my contact at Reese and he said that you would need to get the whole kit, #58238, if you need to replace any of the anchors on the hitch. The single ones are no longer being provided by themselves.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Replacement OEM Puck Anchors for Curt A25 5th Wheel Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching