Seat Bolt/Nut Removal On A Dometic 510 Full-Timer RV Toilet

Question

Question:

Trying to put handle bars That fit under seat. 2 screws In back, is nut under toilet going to fall when I Unscrew the 2 screws.4

asked by: Bob M

0

Expert Reply:

The bolts that attach the seat to the Dometic 510 Full-Timer RV Toilet # DOM29FR are held in place with two plastic nuts that would require you to reach behind the toilet and grip to loosen the bolt and remove the seat. If you didn't grip the nuts they would likely spin with the bolt and never loosen up. The nuts are located in a spot where if they did fall they would just land on the floor of the bathroom.

expert reply by: Kevin C

0

DOM29FR Seat Bolts
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 4

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 5

I would discourage the use of an adapter for use of 2 inch accessories in 1-1/4 inch trailer hitch receivers. The reason is that the adapter places the carrier farther away from the rear of the vehicle and hitch, creating additional torque that 1-1/4…

view full answer...

Answer 6

The Dometic 300 Toilet, #DOM64FR has a total length of 19-3/4" with a minimum distance from wall to center of 8-1/2". The Dometic 320, #DOM87FR is overall length of 22" with a minimum distance from wall to center of 11". If you…

view full answer...

Answer 7

The Dometic 321 Full-Timer RV Toilet #DOM99FR you found is currently the only low profile elongated toilet we carry. We only have this in tan and not white. You can use the Hand Sprayer Kit #DOM75FR to add that feature to this or another Dometic…

view full answer...

Answer 8

The seat height of the Dometic #DOM87FR Full-Timer RV toilet is 18-1/4 inches. I've provided a diagram with all the dimensions for reference.

view full answer...

Answer 9

The Dometic RV toilets like the part #DOM29FR that you referenced use the standard 1/2 inch thread size for the supply line like most toilets do.

view full answer...

Answer 10

The Standard Height models from Dometic are the tallest versions we carry and would be the same as a residential toilet. I've attached a dimensional diagram of the Dometic 320 Full-Timer RV Toilet #DOM87FR you were looking at to give you a better…

view full answer...

Answer 11

On the Dometic Toilet part #DOM87FR the distance from the rear of the toilet to the mounting hole center is 11 inches.

view full answer...

Answer 12

From the furthest point on the back of the Dometic 320 Full-Timer RV Toilet #DOM87FR to the center of the flange bolt hole is 10-3/4". If you only had 11" from the wall to the flange bolts then you would only have a 1/4" of space…

view full answer...

Seat Bolt/Nut Removal On A Dometic 510 Full-Timer RV Toilet

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching