Can Malone Roof Rack Crossbars be Used with Rhino Rack Feet

Question

Question:

Can I use aerodynamic cross bars like the Yakima 60” or Malone 58” with low profile rhino rack crossbar feet?

asked by: Zack

0

Expert Reply:

The feet and crossbars of roof racks need to stick with the same brand as they are not interchangeable. So if you were wanting to use the Malone 58 inch aero crossbars on the roof of your 2007 Toyota 4Runner you'd need to use the roof rack kit part # MPG216.

expert reply by: Jameson C

0

Answer 1

No, the crossbars from the Malone AirFlow2 Roof Rack #MPG217 do not fit the Rhino-Rack legs. You'll need to use the legs that come with the #MPG217.

view full answer...

Answer 2

As seen in the attached photo, the towers on the Malone AirFlow2 Roof Rack - Aero Crossbars 58" #MPG216 and 65" version #MPG217 measure 7" long. I also attached a demonstration video that shows the 58" system being used on a 2019…

view full answer...

Answer 3

The Malone SeaWing #MPG113MD will fit round, square, aero, elliptical, and most factory crossbars. So it will work with your Rhino Rack Aero Crossbars. Just make sure that the measurement from the center of the front crossbar and the center of the…

view full answer...

Answer 4

We have everything you need to complete the roof rack set up on your Forest River No Boundaries travel trailer, which according to my research has the Rhino-Rack RT-Style Roof Rack Tracks #RRRTV148. Like you mentioned, all you need are the towers and…

view full answer...

Answer 5

We do have a trailer hitch receiver and all the parts you need in order to add a 7-way to your 2021 Toyota Sienna, though there isn't a plug-in 7-way, you will need to first add a 4-way and then install a 7-way. The exact parts you need for your…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Can Malone Roof Rack Crossbars be Used with Rhino Rack Feet

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching