Does The Polar Vent for Enclosed Trailers Have An Interior Mounting Piece

Question

Question:

Is there an inside component to this vent or only an outside piece?

asked by: Brian S

0

Expert Reply:

The Vent for Enclosed Trailers # PLR20 would only mount on the outside of the trailer and would not have a piece to go inside of the trailer. I recommend using some butyl tape # AL28FJ on the mounting flange and non-sag sealant # 344270341437-1 around the outer edge for a waterproof seal.

expert reply by: Kevin C

0

Answer 1

To line up where to cut the holes for when installing the Vent for Enclosed Trailers #PLR20 you'd want to drill pilot holes in the surface that go all the way through so that you can line up where the vent will be on the inside of the wall and…

view full answer...

Answer 2

I actually like your first idea better because we have trailer vents that you can install on your door to help keep water spray away from the internal components. Our selection ranges from battery box vents like part #A10-3300BK-05 to ventilator like…

view full answer...

Answer 3

When the Vent for Enclosed Trailers #PLR20 is closed and air is blowing from outside to in there would be a very minimal amount of air that passes through. It wouldn't be a noticeable amount but it's not an air tight seal. There would not be…

view full answer...

Answer 4

The roof vents like the Fan-Tastic part #FV801208 install with a very minimal projection into the interior of the vehicle. If you check out the picture I attached you'll see that the ceiling height of your van would basically be unaffected.

view full answer...

Answer 5

The Vent for Enclosed Trailers - Aluminum - 12-1/4" Wide x 10-1/2" Tall #PLR20 will allow outside air to flow but there is no cubic foot per minute rating as that would require a fan or direct wind for a vehicle sitting still. The fan you…

view full answer...

Answer 6

The Multi-Purpose Ventilator - Aluminum #PLR20 will work to help you move air through your trailer. You may also be interested in the Side Cowl Ventilator with Screen #PLR1715. For the best air movement and still the weather protection, I recommend…

view full answer...

Answer 7

Multi-Purpose Ventilator #PLR20 does not come with hardware and there isn't a specific hardware kit for it. The reason for this is that it can be installed on pretty much anything which means the mounting surfaces can be made of different…

view full answer...

Answer 8

The Polar Multi-Purpose Ventilator #PLR20 has a lever to close the vent when there is risk of heavy rain (please see the linked photo) but the vent will block most water since it also has down-facing louvers on the outside. The lever lets you choose…

view full answer...

Answer 9

We carry a range of complete trailer vents for roofs and walls as well as many replacement parts that you can see on the linked page. From your description it sounds like you may need both a side ventilator like Polar Multi-Purpose Ventilator #PLR20…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Does The Polar Vent for Enclosed Trailers Have An Interior Mounting Piece

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching