Replacement Brake Shoes For Dexter 23-458-00 & 23-459-00 12 Inch Electric Trailer Brakes

Question

Question:

Can you tell be the part number for replacement brake shoes to fit Dexter 023-459-00 and 023-458-00 please? Thank you

asked by: Paul M

0

Expert Reply:

Certainly; the correct replacement brake shoes for the Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" # 23-458 and # 23-459 are the following:

- Replacement Shoe and Lining for Nev-R-Adjust 12" x 2" Electric - Left Hand # K71-675

- Replacement Shoe and Lining for Nev-R-Adjust 12" x 2" Electric - Right Hand # K71-676

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have to adjust…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Replacement Brake Shoes For Dexter 23-458-00 & 23-459-00 12 Inch Electric Trailer Brakes

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching