Where is Hole Location For B&W Gooseneck on 2007 Dodge Ram 2500 With 6-1/2 Foot Bed

Question

Question:

what measurement should I use to center the hole in my bed? 2007 Dodge 2500 Cummins NON Megacab hitch GNRK1313

asked by: BRAD T

0

Expert Reply:

According to the directions I linked below, your 2007 Dodge Ram 2500 with a 6-1/2 foot bed will have a hole 45-1/2 inches from the rear of the truck bed when installing the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit # BWGNRK1313.

expert reply by: Kyle S

0

Answer 1

Since just the brackets of the B and W Turnoverball Hitches are all you need you would want the part #BWGNRM1313 which is confirmed as a fit for your 2007 Dodge Ram 2500 short bed. I attached an install video for you to check out as well.

view full answer...

Answer 2

In regards to the B&W Turnoverball Underbed Gooseneck Trailer Hitch part #BWGNRK1308 which is a fit for a 2007 Dodge Ram 2500 MegaCab, you'll need to drill the 4" hole for the gooseneck hitch ball 45-1/2" forward from the edge of…

view full answer...

Answer 3

Your air bag mounting location will determine compatibility with the Gooseneck trailer hitch #BWGNRK1313. The side plates of the gooseneck trailer hitch #BWGNRK1313 will mount on the outside of each frame rail. See diagram to the right and video…

view full answer...

Answer 4

The side plates of the B&W gooseneck trailer hitch #BWGNRK1313 will mount on the outside of each frame rail of your 2004 Dodge 2500 8-foot bed. See the B&W video I included at the 7 min and 30 second mark. If your Firestone air bags like…

view full answer...

Answer 5

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 6

I spoke to my contacts at our gooseneck manufacturers and they have all said that when their hitch balls or release mechanisms get frozen in the hitches like the part #BWGNRK1313 the best solution is to let it soak for a long time with penetrating…

view full answer...

Answer 7

Yes, the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Rear Axle #AL88375 are compatible with an in-bed hitch like the #BWGNRK1319 you have in your 2021 Ram 1500. These will help keep you level and improve…

view full answer...

Answer 8

For your 2005 Ram 2500, I recommend the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs, #BWGNRK1313. This is a custom fit for your truck that will give you a gooseneck hitch that will keep your truck bed…

view full answer...

Answer 9

The B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit #BWGNRK1308 is for select Ram models/years with a gas engine while the Custom Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitches #BWGNRK1313…

view full answer...

Answer 10

I called B&W and the factory set-up for the Ram 2500 did not start until 2014 and the 2013 has a 6-1/2 foot bed, while you mentioned 6 foot. Would you be able to give me any other information or possibly a photo of what you do have? Or is there a…

view full answer...

Answer 11

I checked with B and W and the correct replacement ball release latch pin handle you are looking for is the part #BW1900-2-2007 that you referenced for your B and W Turnoverball hitch #BWGNRK1111.

view full answer...

Answer 12

That really depends on the clearance you have under the trailer where the spare resides. It's possible you'd have enough clearance but it really depends on where exactly it mounts. If the spare attaches to the cross-member on the front of the…

view full answer...

Where is Hole Location For B&W Gooseneck on 2007 Dodge Ram 2500 With 6-1/2 Foot Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching