Replacement T-Bolt Recommendation for the TruXedo Elevate TS Rails

Question

Question:

Does it fit to Elevate ts rails?

asked by: Arman A

0

Expert Reply:

The Replacement M8 x 16 mm Rectangular Head T-Bolt for Rhino-Rack Accessories # RR89HB is designed to replace any M8 x 16 mm t-bolt so if the t-bolt on your TS Rails for TruXedo Elevate Rack System # TH65FR has the same measurements it'll work, but it has not been confirmed to be a direct replacement.

Another alternative is to use the Replacement T-Bolt for TracRac Ladder Racks # HD-80122 which measures 3/8"-16 x 1-1/8" and will fit in the t-channel.

expert reply by: Bryce D

0

Answer 1

The threaded portion is 1" long on the Replacement M8 x 16 mm Rectangular Head T-Bolt for Rhino-Rack Accessories - Qty 1 item #RR89HB.

view full answer...

Answer 2

Typically for replacing Venture brand landing gear on a trailer the Stromberg Carlson landing gear set part #LG-183708 is all that's needed and normally bolts right up. The dimension you listed is very unusual especially for a Venture brand of…

view full answer...

Answer 3

The Jif Marine Telescoping Gunwale Hook Ladder #JIF28FR measures 38" from the apex of the hook to the bottom step. The spacing between each rung is 11.5". That would make the measurement to the stand-offs from the apex of the hook…

view full answer...

Answer 4

Yes, the TS (T-Slot) Rails for Truck Hero Elevate Rack System #TH75FR will need to be installed underneath the rails of your BakFlip MX4 Tonneau Cover. You could get the Rhino-Rack Vortex Crossbar System #RRVA180B-RRRLT600 which are 71 inches long.…

view full answer...

Answer 5

The correct TS Rails for TruXedo Elevate Rack System for a 2020 Ford F-150 with 5-1/2' or 5' 6" bed is part #TH75FR. This can then be used with Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600 to provide an attachment for a…

view full answer...

Answer 6

Great questions! The Elevate Rack System is available outside of the TruXedo website - we are a great example of that. The TS Rails for TruXedo Elevate Rack System #TH65FR are compatible with a handful of tonneau covers: BAK: G2, MX4, Revolver X2,…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Replacement T-Bolt Recommendation for the TruXedo Elevate TS Rails

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching