How Many SumoSprings Kits Does Reflection 337RLS Need

Question

Question:

My Reflection 337RLS is a tandem axle 5th wheeler. Do I need 2 sets of Sumosprings or will 1 set work?

asked by: A J

0

Expert Reply:

Since your Reflection 337RLS is a tandem axle trailer you would need two sets of the SumoSprings part # SS26MV. This kit is for one axle.

expert reply by: Jameson C

0

Answer 1

Since you have 5,200 lb overslung axles the SumoSprings kit you'll want is the part #SS26MV which has the black spring and is rated for between 5k and 8k axles. This will give you the best ride quality and support like you are needing.

view full answer...

Answer 2

The SumoSprings Trailer Helper Springs #SS26MV are the correct design and weight rating for your 2021 Grand Design Reflection 310RLS. You will need to verify that the u bolt plate is smaller than 5-1/2" wide x 3/4" thick for it to fit…

view full answer...

Answer 3

It appears that your u-bolt plate on your 2021 Grand Design Reflection 31MB, will work with the SumoSprings Trailer Helper Springs #SS26MV. The plate itself including the bends does not appear to be larger than 3/4" nor does the width appear to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You can use that upper hole on your hanger to install the #MR33WR. Make sure you don't tighten it down too much or you will pinch the leaf spring and it won't function properly. You will also need to make sure you have enough room to install…

view full answer...

Answer 6

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 7

Thanks for the pictures! Since your 2022 Grand Design Reflection 303RLS came with the CRE3000 equalizers you will need three of the MORryde X-Factor Crossmember item #MR33WR. It looks like you have the standard 3" wide frame hanger so all of the…

view full answer...

Answer 8

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 9

Sorry for any confusion that may have arose, but what you want is the U-Bolt Kit for Mounting 8,000-lb, Round Trailer Axles #APUBR-35. These are designed for 3 inch diameter, 8,000 lb axles and are compatible with the Roadmaster Comfort Ride Leaf…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

Personally Russ, if you are planning to keep your 2018 Grand Design Momentum 351M toy hauler and want to benefit from a better ride then upgrading to the Roadmaster Comfort Ride Leaf Spring Suspension Kit #RM-2460-2570 makes the most sense. If you…

view full answer...

How Many SumoSprings Kits Does Reflection 337RLS Need

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching