Troubleshooting One Rear Jack Of HappiJac Truck Bed Camper Jacks LC736515-ELKIT Clicking

Question

Question:

i was taking my camper off when one of my rear jacks quit working, when i hit the button i hear a click in side the camper nothing from the jack.

asked by: JOHN S

0

Expert Reply:

Sorry to hear that!

First things first check that you're getting a full 12v (really 12.8v) from the battery to power your Happi Jac electric jacks # LC736515-ELKIT, which you can do with a multimeter # PT29ZR set to read dc volts. If you're not quite getting 12.8v you can run into clicking as there's not enough power for the motor.

If you find you're getting enough power then test the connector for the motor in question to see if you're getting power to the connector.

If you are then the motor is bad and you'll need to replace it with the # LC759927.

expert reply by: Samuel C

0

Answer 1

It sounds like it may be the Circuit Board #LC733513 itself has gone bad. Your current circuit board is compatible with your Remote #LC723915. And I see you have the Remote Cable #LC149557 so it is safe to assume you have done all the proper…

view full answer...

Answer 2

I reached out to Happijac for clarification and I was told there are two different remote types. The remotes with the newer style logic boards have 25 amp fuses. Remotes with the old logic boards have 20 amp fuses. If you look at the rear of the…

view full answer...

Answer 3

The Replacement Remote Control for HappiJac Electric Camper Jack Systems #LC723915 works with logic boards 723914 and 733513. If that matches your circuit board then you can use the remote. You will also need #LC149557 for pairing. If you have one of…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hey Chad this is a great question. So the MORryde ALLTREK part #MR89DR does offer additional vertical suspension but it does sit a little taller than the equalizers it replaces so you wouldn't have to worry about your tires hitting fenders or…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 9

Yes, they are if your axles are overslung and the springs sit on top of them. The SumoSprings Trailer Helper Springs for 5-8K Axles item #SS26MV will work with a triple axle set up. They do a great job of absorbing road shock while also working to…

view full answer...

Answer 10

The two parts you mentioned (#RP87FR and #RP39FR) that fit your 2021 Ford F-350 Super Duty will both allow the ability to pull a gooseneck trailer with a gooseneck ball or use a 5th wheel hitch in the puck system. The only difference between them is…

view full answer...

Answer 11

From the top of the bracket to the bottom of the rubber spring the #TFR350SDJ Timbrens measure about 7-1/2 inches. When installed you ideally want about a 1/2 inch to an inch of space between the Timbren and its contact point. However, to install…

view full answer...

Answer 12

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Troubleshooting One Rear Jack Of HappiJac Truck Bed Camper Jacks LC736515-ELKIT Clicking

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching