Troubleshooting HappiJac Wireless Remote Not Operating Truck Camper Jacks

Question

Question:

Hello, I recently bought a 2005 Artic Fox from a widow with electric Happijac truck camper jacks. The camper had a new remote that had never been used. It is part #723915 for the remote but I cant seem to find a part number on the circuit board anywhere. It has 30 amp fuses in it. Ive went through all the troubleshooting here that I could find but nothing seemed to work. The green light on the remote comes on but the remote wont operate the jacks even after a reset. Could it be that this remote is not compatible with the circuit panel. Thanks

asked by: John G

0

Expert Reply:

It sounds like it may be the Circuit Board # LC733513 itself has gone bad. Your current circuit board is compatible with your Remote # LC723915. And I see you have the Remote Cable # LC149557 so it is safe to assume you have done all the proper troubleshooting and tried to operate the jacks with the remote connected. The new Circuit Board # LC733513 is an upgraded unit and will work with your same remote.

expert reply by: Bud M

0

Answer 1

No, you won't need a new remote, however for a replacement circuit board you're going to want the Replacement Circuit Board for HappiJac Electric Truck Camper Jack Systems #LC733513 which is going to be a direct replacement.

view full answer...

Answer 2

The Replacement Remote Control for HappiJac Electric Camper Jack Systems #LC723915 works with logic boards 723914 and 733513. If that matches your circuit board then you can use the remote. You will also need #LC149557 for pairing. If you have one…

view full answer...

Answer 3

Sorry to hear that! First things first check that you're getting a full 12v (really 12.8v) from the battery to power your Happi Jac electric jacks #LC736515-ELKIT, which you can do with a multimeter #PT29ZR set to read dc volts. If…

view full answer...

Answer 4

I reached out to my contact at Lippert, and she confirmed that you will be able to use the Clutchless motor head #LC759927 on your 4800 Happijack jack as a replacement for your current clutched motor head LC182515. However, you will need to have the…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The Yakima EXO Swing Away 2 Bike Rack w/ Enclosed Cargo Carrier #Y34ZR will restrict the passenger side door on your 2024 Entegra Expanse. When the arm swings out it will be sitting at that corner of the vehicle which means the door will be able to…

view full answer...

Answer 9

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 10

Hey Al, this is a great question but since you have free-backing plates now you would never need to mess with the manual lock out of your Atwood coupler.

view full answer...

Answer 11

Hey Chad this is a great question. So the MORryde ALLTREK part #MR89DR does offer additional vertical suspension but it does sit a little taller than the equalizers it replaces so you wouldn't have to worry about your tires hitting fenders or…

view full answer...

Answer 12

The 1-5/16" Hellwig Adjustable Big Wig Rear Anti-Sway Bars are designed for 2WD #HE97MR or 4WD #HE94FR versions of your 2021 Ford F-250. These are both designed for trucks which have a stock ride height. Hellwig does offer their 2" Lift…

view full answer...

Troubleshooting HappiJac Wireless Remote Not Operating Truck Camper Jacks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching