Brake Line Reducer Fitting for Back of Trailer Actuator

Question

Question:

I have a Tiedown Model 660 brake actuator on a trailer with drum brakes and need the brake line adapter that screws into the back of the cylinder for the line out to the trailer. I brake line has a male fitting, 3/8inch x 24 ?

asked by: Dennis H

0

Expert Reply:

Sounds like what you need is the part # T4750200. This has thread fittings of 1/8" NPT female 1/2"-20 NPT male.

expert reply by: Jameson C

0

Answer 1

What you need is the adapter #T4750200 which will adapt your current brake lines to the solenoid part #T4748800 that you have now.

view full answer...

Answer 2

Since you have a Titan Model 10 actuator and need a new adapter to go from the master cylinder to the lock out solenoid you'd need the part #T4750200 that you referenced.

view full answer...

Answer 3

For your surge brake coupler, you will need the Replacement Solenoid Adapter Fitting for Titan Model 10 Brake Actuators #T4750200 or a complete unit like the Replacement Solenoid Valve for Titan Brake Actuators with Reverse Lockouts #T4748800 only if…

view full answer...

Answer 4

The adapter fitting #T4871700 is a 3/16 inch male inverted flare. The other end is a 1/4 inch and fits onto a 1/4 inch brake line so it can be attached to a 3/16 inch fitting

view full answer...

Answer 5

The part you are looking for is the Brass Connector for Titan Disc Brake Kit, #T4750300. This is the fitting that threads into the master cylinder that accepts the reverse lockout solenoid on your Titan actuator. I have attached a link to this part…

view full answer...

Answer 6

If you are talking about the small opening on the outside and inside of the Orifice Connector #T1209800 then those measure 0.0010" and 0.0865" respectfully. I went out to the warehouse and measured them with the digital caliper. Please note…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Brake Line Reducer Fitting for Back of Trailer Actuator

Product Page this Question was Asked From

Continue Researching