Recommended TorkLift Camper Tie-Downs For A 2017 Chevy Silverado 3500

Question

Question:

Hi. I want to confirm fit for Torklift camper tiedowns. The truck is a 2017 Chevy 3500HD, Crew cab, 6.5 ft bed. The tubular runnin boards extend just a little past the cab/bed interface. From the Torklift website it looks like I need C2220 front and C3215 rear. Im also wondering if you know what Torklift fastgun turnbuckles Id need for that setup. I can send a picture of the truck, if needed. Thanks,

asked by: Aaron H

0

Expert Reply:

TorkLift doesn't list a fit for the front tie-downs if the running board extends past the cab so you'll want to refer to the picture I have below that took from Rob's installation video and compare it to how your running boards sit. Worst case scenario you'll have to remove the running boards and replace them with something else to get your tie-downs in place. You're correct that you'll need the TorkLift # TLC2220 and # TLC3215.

For the turnbuckles you'll want the TorkLift Locking FastGun Turnbuckles for Frame-Mounted Tie-Downs # TLS9522-2-LK.

expert reply by: Kevin C

0

Answer 1

While you are correct that the hitch you have on your 2015 GMC Sierra 1500 is one of the factors for finding the correct camper tie-downs, but most work with both factory hitches and non-torklift aftermarket hitches. You only need more specific…

view full answer...

Answer 2

For your 2020 Chevy Silverado 2500 with 6-3/4 foot bed, the front #TLC2225 and rear tie down #TLC3221 are the correct fit for your truck. Whether you have the double cab or the crew cab and whether you have running boards or not these are the…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 7

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Recommended TorkLift Camper Tie-Downs For A 2017 Chevy Silverado 3500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching