Determining The Correct Replacement Door Lock For A Coachmen Freedom Express 274rks

Question

Question:

Will this lock fit my Coachmen Freedom Express 274rks?

asked by: Steven B

0

Expert Reply:

To know if the Global Link Ultra E Pro Electronic Lock for Travel Trailer # 295-000183 would fit in your door you'll first need to remove the current handle and measure the cutout hole. The # 295-000183 requires a 3-3/4" tall x 2-3/4" wide cutout hole in order to fit. I've attached a short video below where I'll walk you through measuring the cutout hole and how to install this door lock.

If you find that your cutout hole is a different size then let me know and I'd be happy to find the correct replacement.

expert reply by: Kevin C

0

Answer 1

Based on your pictures, it appears that you need a right hand door lock. You will need to remove the 4 bolts on the inside of the latch to remove the cover plate and measure the size of the cut out in the door to make a good choice. The Bauer BA76FR…

view full answer...

Answer 2

The Bauer Products Motorhome Door Lock part #BA64FR will fit any motorhome or trailer with a latch cutout that is 5-1/4" wide x 4-1/2" tall or can be opened up to such. The door thickness must also be between 1-1/4" to 1-1/2"…

view full answer...

Answer 3

The closest match we have for you is the Bauer Products Motorhome Door Lock #BA64FR, which will fit cutouts that are 5-1/4" wide by 4-1/2" tall. This will require you to trim your existing latch opening to ensure a proper fit.

view full answer...

Answer 4

Lock assemblies can be different sizes and still use the same latch cutout sizes. The Global Link RV Entry Door Locking Latch Kit with Keyed Alike Option - White #295-000021 will fit into latch cutouts that are between 2-1/2" wide x 3-1/2"…

view full answer...

Answer 5

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

We do carry the Dometic RV Water Heater #DMC74FR which you could use to replace your Atwood G6A-8E 6 gal RV Water Heater, but I highly recommend switching over to a tankless system like the Furrion RV Tankless Water Heater 60,000 BTU #FR98SR. This…

view full answer...

Answer 10

We may have some potential options for replacing the tack room door lock on your Featherlight trailer. Is the 5" L x 5" H dimension you gave for the door cutout or the lock itself? The best way to find the right replacement lock is to go by…

view full answer...

Answer 11

I think I have a solution for you in the Global Link RV Entry Door Locking Latch Kit, #295-000021 for white or, #295-000019 for black. This latch kit measures 3.47" wide x 4.28" tall, fits doors that are 1-1/4" to 1-1/2" thick,…

view full answer...

Answer 12

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...