Correct Replacement Side Seal for an Extang Solid Fold 2.0 On a 2022 Ford F-150

Question

Question:

The side seal on one of the panels came off. Will I be able to cut this it fit? Extend solid fold 2.0 on a ‘22 f150

asked by: Chad

1

Helpful Expert Reply:

Yes you can use the Replacement Side Seal for Extang Solid Fold 2.0 Tonneau Covers # EX32560368 as a replacement for your Extang Solid Fold 2.0 that's missing a side seal.

This seal measures 68-1/2" long however it can also be trimmed if need be.

expert reply by: Bryce D

1

Answer 1

I reached out to Extang and the Replacement Side Seal for Extang Tonneau Covers part #EX32560368 is the correct seal to replace the damaged one on your Extang Trifecta 2.0 Tonneau Cover.

view full answer...

Answer 2

The corner piece of your Extang SolidFold 2.0 is only available with an entire replacement tail panel. But I do have some good news, if the seal is the only issue; we have replacement seals available. We have the Replacement Tailgate Seal for Extang…

view full answer...

Answer 3

The Replacement Tailgate Seal for Extang Solid Fold 2.0 Tonneau Covers #EX32563200 is approximately 1 inch wide.

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Yes, the B and W Turnoverball rail kit part #BWGNRK1057 that you referenced does fit the 2009 Chevy Silverado 1500 5-1/2 foot bed.

view full answer...

Answer 10

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 11

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 12

We currently offer 3 different replacement strap hinges, #2008-8, #2512, and #2212, for cargo trailers. I have included a photo showing each of these with their measurements listed. I recommend comparing these measurements to the strap hinges on your…

view full answer...