Does B and W Turnoverball BWGNRK1057 Fit 2009 Chevy Silverado 1500 5-12 ft Bed

Question

Question:

Will this fit a 2009 GMC Sierra 1500 with a 51/2 ft box?

asked by: Gary P

0

Expert Reply:

Yes, the B and W Turnoverball rail kit part # BWGNRK1057 that you referenced does fit the 2009 Chevy Silverado 1500 5-1/2 foot bed.

expert reply by: Jameson C

0

Answer 1

My technical contact at AirLift confirmed that the minimum pressure setting for triggering automatic re-filling of the air bags by the WirelessONE Compressor #AL25980 can be changed from the typical 5-psi to 10-psi by putting this setting into one…

view full answer...

Answer 2

We carry many fenders, though we do not have a list of parts specific to any type of trailer. I have added a link for you to each of our available fenders to take a look at. You will need to know the size of your tires as well as the length of…

view full answer...

Answer 3

In regards to the B&W Turnoverball Underbed Gooseneck Trailer Hitch part #BWGNRK1057 which is correct for a 2015 GMC Sierra 1500, you'll need to drill the 4" hole 44-1/8" from the rear edge of the truck bed. This is…

view full answer...

Answer 4

The issue you will run into is that when you go to make tight turns the storage area on your trailer (depending on the dimensions of it), will most likely hit the cab of the truck since your truck bed is so short. Here is a formula you can use to…

view full answer...

Answer 5

For a tandem axle trailer rated for 7000 lbs, you can use either a Load Range C or D tire. Each axle will be rated for 3500 lbs so you need a tire that will carry 1/2 that capacity. That would make your minimum load range before limiting your…

view full answer...

Answer 6

The standard air tubing diameter for Air Lift and Firestone air bag kits is 1/4 inch like the part #F2012 that you referenced. Firestone and Air Lift do not make a smaller diameter tubing at this time.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Does B and W Turnoverball BWGNRK1057 Fit 2009 Chevy Silverado 1500 5-12 ft Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching