Solution for Lost Key for Bauer Products RV Baggage Door Slam Latch

Question

Question:

Hi, I recently bought a trailer with a Bauer baggage lock but do not have the key for it. Is there a way to get one or would I have to buy a whole new lock?

asked by: Vitaly E

1

Helpful Expert Reply:

Without a key number there isn't a way unfortunately. It would be nice if they put the key number on the latch somewhere but they do not do that. You would need to replace the slam latch with part # BA57FR.

expert reply by: Jameson C

1

Answer 1

Yes. As long as you have a 3" wide channel tongue, you can use the Demco Hydraulic Trailer Actuator #DM72VR as a replacement for your current actuator. For new brake lines you'll want to use the Kodiak Hydraulic Brake Line Kit #18SI-BLKIT…

view full answer...

Answer 2

Brake lines don't have to be difficult to run. I recommend the Kodiak Hydraulic Brake Line Kit - Single Axle - 18' #18SI-BLKIT. This will give you one 18 foot flexible line and one 7 foot line and one 1-1/2 foot long line along with the tee…

view full answer...

Answer 3

The best brake line kit for a single axle boat trailer is the Kodiak Hydraulic Brake Line Kit part #18SI-BLKIT which works with boats that have torsion or leaf spring axles as well as those with disc or drum brakes. The Kodiak Hydraulic Brake Line…

view full answer...

Answer 4

The best solution we have is going to be a new surge coupler like the #099-175-00. Some of the Dico and Titan parts are interchangeable in recent years but since your trailer is almost 30 years old it's tough to say what all would still work.…

view full answer...

Answer 5

The #20TA-BLKIT brake line kit you referenced is indeed compatible with the #AKUBRK-35-D Hydraulic Brake assemblies you'd looked at, the line kit is compatible with bolt disc and drum brake systems. The brake assemblies will be compatible with…

view full answer...

Answer 6

Thank you for the photo of your trailer hub/drum assembly which shows its diameter to be 10-inches. More than likely the drum depth dimension is 2-1/4-inches since 10 x 2-1/4-inch hubs are quite popular. Please refer to the photo I linked for you.…

view full answer...

Answer 7

Since your tandem axle trailer only has brakes on one of the axles, you will just need a single axle kit like the Kodiak Hydraulic Brake Line Kit #18SI-BLKIT you were looking at. This kit includes an 18 foot, 7 foot and 1-1/2 foot long flexible brake…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Solution for Lost Key for Bauer Products RV Baggage Door Slam Latch

Product Page this Question was Asked From

Continue Researching