Correct Replacement Roof Vent Cover for Livin Lite Trailer

Question

Question:

I am needing to replace the vent covers on my Livin Lite Travel Trailer. I am having a difficult time locating the correct part/part number. The lens has cracked on both of them.

asked by: Victoria L

0

Expert Reply:

I am not sure which vent these trailers use but what you can do is go with a universal cover like the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent part # MA00-335001 for white or part # MA00-335002 for smoke. If you don't want to go with universal then you'll need to know you vent model number found on the sticker inside the frame.

expert reply by: Conner L

0

Answer 1

The correct replacement lid/dome for a MaxxFan* 4751KS is the Replacement Lid for MaxxFan and MaxxFan Plus Roof Vents part #MA10A40009K for black or part #MA10A40002K for white.

view full answer...

Answer 2

Entry door locks, like the Bauer Products #BA64FR, typically will have a sticker on the inner handle portion that sits inside your RV, but I have installed a few where they also have the key code on a sticker on the inner components of the handle.…

view full answer...

Answer 3

As it turns out, almost all trailer roof vents are 14" X 14", +/- 1/4". Your best choice is the MaxxAir #MA00-335001 Universal Replacement Lid. The continuous hinge versions are better than the 3-tab versions. The hinge on…

view full answer...

Answer 4

Hey Thomas, If your roof vent is 14" x 14" then you could go with the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent #MA00-335001. This replacement is a universal-fit for Elixir, Ventline, Jensen, Hengs, and…

view full answer...

Answer 5

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 6

With the pandemic and Dometic taking over Atwood's water heater division it has been very hard to come by replacements. My honest recommendation is to go tankless and replace your Atwood GCH10A-4E with the Furrion RV Tankless Water Heater 60,000…

view full answer...

Answer 7

We carry replacement lids for trailer roof vents along with covers and other parts, and we offer complete vent units too. All of these item types can be seen on the linked page. If you need only a replacement lid simply click on that image at the top…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 10

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 11

There unfortunately isn't a guide to tell us the equalizer, shackle straps, and leaf spring sizing for your 2016 Grand Design Reflection 313RLTS so you'll need to a bit a of measuring to determine the best replacements. Before measuring…

view full answer...

Correct Replacement Roof Vent Cover for Livin Lite Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching