Recommended Center Cap for Dexstar Steel Mini Mod Trailer Wheel - 16" x 6" Rim - 6 on 5-1/2

Question

Question:

Center caps for trailer wheels

asked by: Joseph M

0

Expert Reply:

If you're looking for a center cap for the Dexstar Steel Mini Mod Trailer Wheel part # AM20742 then we have just what you need, the Americana Trailer Wheel Center Cap part # AM90077 which is an exact match made of stainless so it won't rust and has a removeable center cap so you can grease your spindles if they have a built-in zerk.

expert reply by: Conner L

0

Answer 1

I spoke with my contact at Ventline and she stated that if you have a newer EZ Lift Ventadome, the correct replacement lid will be part #BVE0108-03. This smoke color lid features a plastic hinge with four mounting points. You can compare the hinge…

view full answer...

Answer 2

When installing the Fastway e2 Weight Distribution w/ 2-Point Sway Control #FA94-00-0600 referenced in your question, you will need a torque wrench capable of 250 ft-lbs of torque. With the weight distribution engaged, you will begin with the angle…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 6

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 7

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

Hey Paul, we have a Blue Ox base plate kit that fits your 2024 Nissan Versa with the part #BX1856. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle.…

view full answer...

Recommended Center Cap for Dexstar Steel Mini Mod Trailer Wheel - 16" x 6" Rim - 6 on 5-1/2

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching