Length of Replacement Mounting Hardware for Recovery Tracks for Yakima Ladder Racks

Question

Question:

What size are these bolts? Are they M8 or M6? Length of threads 12mm or 16mm?

asked by: Jorge

1

Helpful Expert Reply:

The Replacement Mounting Hardware for Recovery Tracks for Yakima Ladder Racks part # Y83FR are M8 x 18mm.

expert reply by: Conner L

1

Answer 1

The Yakima Replacement Anchor Plate Style-A, Part #Y8810074, comes as a set of 8 plates that measure 3/4-inch x 7/8-inch. The centered threaded hole measures 0.2 inches (or 5.1 millimeters) in diameter. Please refer to the photo provided. The Yakima…

view full answer...

Answer 2

The Replacement Mounting Hardware for Recovery Tracks for Yakima Ladder Racks part #Y83FR uses M8 hardware per Yakima.

view full answer...

Answer 3

We do offer replacement nut plates in a hardware bag, part #Y83FR. Yakima doesn't offer the nut plates separately.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR for your 2023 Toyota Tacoma with the factory tow package. You will be able to connect the wiring using the Redarc Adapter #RED99FR directly to the factory connector. We also have the…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...