Recommended Replacement Jack for Exiss Horse Trailer

Question

Question:

I have a 10400lv GVWR, 2001 Exiss 3 horse slant trailer. I have tried to replace the parts inside the jack but nothing seems to fit, so I feel like a whole new jack is the answer. What do you have for a bolt on jack that would work for this type of trailer? Do they make a bold on jack? Any help is appreciated. Thank you.

asked by: Melanie K

0

Expert Reply:

I might have an option for you but I don't know what exact jack you have on your Exiss Horse Trailer. That said, they are usually welded so there's not really a bolt-on replacement. The Buyers Products Heavy-Duty 4" Square Jack part # 3370091415H is a good option to start with, it has a 12,000 lb capacity and features a weld-on install.

I have attached a full list of our jacks below as well if this won't work.

expert reply by: Conner L

0

Answer 1

There is always a way to make it work. I can't recommend doing that as I have not tested it and I do not offer a product like that with the exception of the Dexter Trailer Springs Over-Under Conversion Kit part #K71-384-00. This will give you a…

view full answer...

Answer 2

I sent your axle info to Dexter and they were able to determine that you have a set of 7k Dexter Torflex axles so the correct lift you need is the part #K71-725-02 which will give you a lift of 3-1/8 inches.

view full answer...

Answer 3

I have the correct kit for you! The SLR P-15 unfortunately does not designate the particular model Dexter Torflex axle you have. However, given the 7,000 pound weight capacity of your axles, you either have the tandem Torflex #12, #12T, or #12V…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 6

The best way to confirm the weight capacity of your Dexter Torsion Axles is to find the lot number on the axle tag which is located on the center of the axle on the rear side. This tag should say Dexter Axle and then a 9 digit number. The number you…

view full answer...

Answer 7

Interesting. We don't have that specifically, but there are a couple of routes you could go. Most trailers will use the Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1 #TJSC-24 for stability in the corners so you could mount a…

view full answer...

Answer 8

I went ahead and reached out to RAM and they explained to me that to re-install your inner leg to your RAM jack like the Square Direct Weld Jack - Drop Leg w/ Spring Return #TJD-12000SP-R2NH, you are going to need to re-install the lower pin, replace…

view full answer...

Answer 9

The Ram 14K jacks don't have a replacement rod and nut available like the 12K #TJD-12000-RODNUT and are no longer available in that capacity. I recommend changing out your jacks for the 12K option. You can use the Bulldog Side Wind Jack Assembly…

view full answer...

Answer 10

The valve stem isn't included with the Americana wheel #AM20552. The valve stem I recommend is the Americana snap-in part #AM20904 as it will have a psi rating up to 80. I included a couple video reviews on each tire for you as well.

view full answer...

Answer 11

We have the Buyers Products Heavy-Duty 4" Square Jack w/Front Pin Drop Leg #3370091415H that matches the design of the jacks on your gooseneck trailer. We will only have the jack assemblies and will not have the crossover tube or handle…

view full answer...

Recommended Replacement Jack for Exiss Horse Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching