Replacement Box Plate For Thule Excursion Roof Top Cargo Box Manufactured In 2007

Question

Question:

I have a Thule Excursion that was made in 2007. Im missing one of the flat plates. The two holes appear to be 4inch apart. Will this fit?

asked by: James

0

Expert Reply:

Your Thule Excursion will need the Replacement Box Plate # TH10378. This is the specific plate listed from Thule. I do see the Plate # TH04998 you found is very similar with both having holes at 4" on center. The difference I see is the one you found is 5"x3" while the one Thule lists is 5-1/2"x2-1/2".

expert reply by: Bud M

0

Answer 1

The distance between the holes of the #TH04998 is 4 inches. The width of the plate is 5 inches and depth would be 3 inches.

view full answer...

Answer 2

The ES in the Frontier ES means easy snap. As you have already guessed, the hole spacing is different and you would have to modify the box in order to use an alternate mounting kit on a non-ES box. Modifying the box will compromise the structural…

view full answer...

Answer 3

I spoke with my contact at Thule and she informed that you could not use the Easy Snap Hardware on your older Thule Frontier box. She said you would have to use the same hardware that came with your box. If you need replacement hardware you would…

view full answer...

Answer 4

I checked with Thule and the Summit cargo box used the QM3 hardware #TH04997. For just the bolts you would need 4 Carriage Bolt M6-1 x 75mm - Fully Threaded, part #TH10403. The box plate is part #TH04998 and the Replacement Tie-Down Bracket…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Replacement Box Plate For Thule Excursion Roof Top Cargo Box Manufactured In 2007

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching