Hole Dimensions of Thule Mounting Plate # TH04998

Question

Question:

Can you tell me the dimensions of this product? Spacing between holes, etc.

asked by: Eric B

0

Expert Reply:

The distance between the holes of the # TH04998 is 4 inches. The width of the plate is 5 inches and depth would be 3 inches.

expert reply by: Jameson C

0

Answer 1

Your Thule Excursion will need the Replacement Box Plate #TH10378. This is the specific plate listed from Thule. I do see the Plate #TH04998 you found is very similar with both having holes at 4" on center. The difference I see is the one…

view full answer...

Answer 2

I spoke with my contact at Thule and she informed that you could not use the Easy Snap Hardware on your older Thule Frontier box. She said you would have to use the same hardware that came with your box. If you need replacement hardware you would…

view full answer...

Answer 3

The ES in the Frontier ES means easy snap. As you have already guessed, the hole spacing is different and you would have to modify the box in order to use an alternate mounting kit on a non-ES box. Modifying the box will compromise the structural…

view full answer...

Answer 4

You will need to confirm the dimensions on your current mounting plate with the Replacement Plate Box Support for Adventurer Cargo Box #TH10378. I spoke to Thule and they could not confirm that it was the correct plate since there are different…

view full answer...

Answer 5

It is not a huge deal to add a few new mounting holes to the bottom of an ABS plastic cargo box like the Yakima SpaceBooster. A cordless drill and appropriately-sized drill bit will make short work of it. I would avoid using a heated implement for…

view full answer...

Answer 6

For the older Yakima SpaceBooster all we have is the Yakima Replacement Luggage Knobs #Y8870048 which is new knobs. Since the box is so old the rest of the parts for the box have been discontinued.

view full answer...

Answer 7

Yes, the U-Bolts that come with the Replacement Mounting Hardware for Car Top Cargo Roof Cargo Box #CTC-18PARTS have a 3/16" diameter and are spaced 4" apart on center. I have attached some photos to demonstrate this and some other…

view full answer...

Answer 8

I can help you. I have included a picture that shows how that type of Yakima hardware goes together. With that image you should have no trouble getting everything together in the right order.

view full answer...

Answer 9

For your Thule Summit Cargo Box, the correct mounting hardware kit is the QM3 Quick Mount Hardware #TH04997. This kit includes all of the needed mounting hardware to attach the Thule Summit to the crossbars on your vehicle's roof. We do also have…

view full answer...

Answer 10

The correct wing nuts for the Yakima Replacement Long Mounting Bolts, #Y8870068, are the Yakima Luggage Knobs, #Y8870048. The luggage knobs come in a package of 8 to match the replacement bolt kit. The specs of the bolts and wing nuts are not listed…

view full answer...

Answer 11

I checked with Thule and the Summit cargo box used the QM3 hardware #TH04997. For just the bolts you would need 4 Carriage Bolt M6-1 x 75mm - Fully Threaded, part #TH10403. The box plate is part #TH04998 and the Replacement Tie-Down Bracket…

view full answer...

Answer 12

We sell the Replacement 3-Wing Hand Knob for Thule Cargo Boxes, part #TH04877, that come in the Thule QM3 Quick On-Off Mounting Hardware Kit for Adventurer Cargo Box, part #TH04997. You would also need 4 Carriage Bolt M6-1 x 75mm - Fully Threaded,…

view full answer...

Hole Dimensions of Thule Mounting Plate # TH04998

Product Page this Question was Asked From

Continue Researching