Replacement Crossmember for 2012 Keystone Montana Mountaineer 375FLF Landing Gear

Question

Question:

I have a 2012 montana,keystone,mountaineer 375FLF. looking for the bar inside the front compartment that goes between the two legs to run both legs what size is the hole that runs between both hadualic legs that a pin that goes in

asked by: Choya U

0

Expert Reply:

For a replacement crossmember you can use the Replacement Cross Members for Stromberg Carlson Landing Gear # SC46MR. This will run between the drive shafts on your front landing gear and extends from 40-1/2" to 68-1/2" wide.

expert reply by: Robin H

0

Answer 1

The Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs #LG-142178 is the correct replacement motor for the discontinued Atwood 75721. The #LC141893 you asked about will also work and is a higher speed motor so it will give you…

view full answer...

Answer 2

We do have the correct replacement for your Atwood 71119 landing gear motor, which is what is shown in your photo. The replacement part is the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893. I have added a link to a…

view full answer...

Answer 3

The crossmember shafts for Stromberg Carlson Landing Gear #LG-1 are available with part #SC46MR. To attach the crossmembers to the legs you'll want to re-use the 1 ½” x ¼” bolts and nylon lock nuts that are currently on your system…

view full answer...

Answer 4

There is a heavier-duty option to replace the Venture M-9000-PK landing gear motor than the 5,000 lb capacity Lippert Venture 5th Wheel RV Landing Gear Motor #LC142178. While that is the correct fit, if you want a higher rated capacity you can…

view full answer...

Answer 5

The Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs item #LG-142178 you were looking at is the correct replacement motor for the discontinued Atwood 75721. The Gearbox for Venture Electric 5th Wheel RV Landing Gear…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...