Is There a Replacement Latch for the Shelby 5135 Trailer Coupler

Question

Question:

I need a repair latch for a Shelby 5135 and dont find a current reference for it on your website. Do you have one?

asked by: Sid B

1

Helpful Expert Reply:

I do have an option for you but Shelby is no longer in business so replacement parts are not on the table. That said, we do have a full replacement option for you in the Channel Tongue Trailer Coupler part # CT-5003-Z which is a direct fit so there's no drilling required.

expert reply by: Conner L

1

Answer 1

The Channel Tongue Coupler part #CT-5003-Z will work great for your situation. It fits the 3 inch channel you have, has more than enough weight capacity at 5,000 lbs trailer weight, and fits a 2 inch hitch ball. Since you have to drill your trailer…

view full answer...

Answer 2

Yes, the Sleeve-Lock Trailer Coupler #CTA-196 will fit the channel bracket that comes with the Brophy Lunette Ring w/ 3-Position Adjustable Channel Bracket #BR43ZR. The bolt holes match as well when it comes to size and spacing so you'll be…

view full answer...

Answer 3

I do have a solution for you but unfortunately, the CA-5100-RK isn't compatible with your Shelby 5135 coupler. While there isn't a repair kit available for your coupler, replacing the entire unit is just as cost effective. For a very…

view full answer...

Answer 4

I recommend etrailer.com Channel Tongue Coupler part #CT-5003-Z to replace the Shelby 5135 coupler. The etrailer.com coupler has a channel width of 3" and takes a 2" ball. It also has 3" from center of bolt hole to center of bolt hole…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Is There a Replacement Latch for the Shelby 5135 Trailer Coupler

Product Page this Question was Asked From

Continue Researching