Handle Recommendation for the Valterra Baldex Valve Body for RV Black Water Tank

Question

Question:

Apparently I need a handle for this I thought it was a screw on Ive never seen this type of stem tell me where I can get a handle

asked by: Rick H

0

Expert Reply:

For your Valterra Bladex Waste Valve Body for RV Black Water Tank w/ Drilled Stem # T1003DSPB you'll just need the Valterra Cable with Valve Handle # TC120PB.

expert reply by: Bryce D

0

Answer 1

To install the Valterra Cable with Valve Handle #TC72PB you will need to simply follow the instructions that are included in the packaging: Remove the locknut from the cable housing assembly. Feed the cable through the mounting bracket or hold in the…

view full answer...

Answer 2

We do have a 3 inch waste valve for a black water tank that allows you to use a cable; the Valterra valve we offer has a drilled stem that allows you to attach your cable. What you are looking for is the following: - Valterra Bladex Waste Valve Body…

view full answer...

Answer 3

You will not have to put any type of sealant on the Sturgis Propane Pigtail #100575-12-MBS becuase the fitting type is an inverted flare. If you are wanting to take the precaution just to prevent the waist of your gas and/or wanting to prevent the…

view full answer...

Answer 4

I checked with my contact at Lippert and he tells me that the #LC149557 is different from a standard phone cord since it is designed to work with logic boards that are specific to HappiJac components.

view full answer...

Answer 5

The Valterra Waste Valve Extension Tube #TX9HPB installs by simply threading onto the valve shaft as you can see in the accompanying photo; it replaces your current handle so that 9 inch measurement would be from the top of the valve shaft. There are…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Handle Recommendation for the Valterra Baldex Valve Body for RV Black Water Tank

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching