Correct Replacement Pitch Arm for Solera 63" Awning Support Arm

Question

Question:

I bent the 63 lippert adjustable pitch awning arm. Can I replace with a 69 lippert awning arm? I have room for extra length. This is for a 2022 KZ Esacpe E20 Hatch

asked by: Michael M

0

Expert Reply:

If your existing support arms measure 63" long end to end then the correct replacement pitch arm is the Replacement Pitch Arm for Solera XL Flat RV Awnings part # LC67VR for black or part # LC62NJ for white. The pitch arm for a 69" long support arm will not fit.

expert reply by: Conner L

0

Answer 1

It's likely you need the Solera 63" Short Awning Support Arm part #LC97UD. In regards to finding a replacement, simply measure the length of the wall-mount extrusion from top to bottom. There are standard lengths; the short styles…

view full answer...

Answer 2

The only way that we have the Replacement Pitch Arm for Solera Flat RV Awnings w/ 69" Long Support Arms #LC375994 (black) available in white is with the entire support arm assembly. - Replacement Support Arm Assembly for Solera Flat RV…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

Hey John, Thanks for the purchases and you have everything you need except the wedge. I verified directly with Reese that the correct wedge to use with the Demco Recon 5th Wheel Trailer Hitch #DM8550043 and Reese Sidewinder #RP34FR is the following:…

view full answer...

Answer 5

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Answer 6

Since you have a tandem axle trailer rated for 10,500lbs the 6-Leaf Double-Eye Spring for 5,300-lb Trailer Axles #e76SR are going to be the closest leaf springs we have to that weight capacity. These springs measure 24-7/8" from center of eye to…

view full answer...

Answer 7

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Answer 10

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

Answer 11

The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57531 will fit your 2022 Ram 3500 Mega Cab with single rear wheels. This is the extra heavy duty 7,500 lb kit so it is most commonly used on dually trucks, but it will fit single rear wheel models…

view full answer...

Answer 12

Yes, the Curt CrossWing Lightweight Gooseneck-to-5th-Wheel Trailer Hitch Adapter #C32DR will work with the OEM puck system on your 2016 Ram 2500. Do understand since you do have the short bed you will likely not be able to make full jackknife turns…

view full answer...